Package include:
4Pcs 23HS2430B Nema23 Stepper Motor 112mm,425oz-in,3A4Pcs CW5045 stepper motor driver 24-50V DC,4.5A1Pcs 400W 36V DC 11A DC switching power supply1Pcs 4 Axis USB Mach3 Motion Control Card1Pcs USB cable1Pcs CD disk
Motor Type: HybridStep Angle: 1.8 degreeHolding Torque: 425oz.in/2.8NmRated Current/phase: 3APhase Resistance: 1.6ohms ; Inductance: 6.8mH+/-20%(1KHz)
Frame Size: 57 x 57 x 112 mmBody Length: 112mmNumber of Leads: 4Weight: 1.66kgFront shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length
Our motor is made of solid and durable metal. The perfect combination of rubber and rotor makes the internal structure more stable, and also reduces the vibration and noise when the engine runs.The motor runs more quietly, with a high torque of 425oz in. The coil uses pure copper enamelled wire to ensure that long-term operation will not lead to excessive engine temperature.The rotor surface is coated with high-quality epoxy resin adhesive to isolate the adsorbed burrs on the rotor surface, more stable magnetic field and longer service life of motor.
Stepper motor's red wire connect to driver's A+ portStepper motor's green wire connect to driver's A- portStepper motor's yellow wire connect to driver's B+ portStepper motor's blue wire connect to driver's B- port
Electrical Specification
Dual Shaft
Material
Wiring
GND：DC power cathodeVCC+：DC power positive poleGND：DC power cathodeA+、A-：Stepping motor one windingB+、B-：Stepping motor other windingPUL+、PUL -：Stepping pulse input+5VDIR +、DIR-：Stepping motor direction inputENA+、ENA- : no need to connect
Dimensions: 118mm×76mm×33mmShape design is convenient for installationWorking environment: Temperature -15-40℃ Humidity<90%
High-performance motor driverMircostepping: 1(1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5, 1/10, 1/25, 1/50, 1/125, 1/250DC power input type: 24V~50VDCOutput current: 1.3A-4.5APhase: 2 phaseWeight:＜300g
Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.Support for connecting electronic handwheel;MCU model: three generation 32-bit STM processorCommunication plug-in: RnR motion control card - ECO-2.0
4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device.
Support for 4 Axis linkage, you can connect four stepper motor drives or servo drives;Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;Have 0-10V signal output,you can use mach3 software to control the spindle motor speed.One status LED, indicate connection status on the board.
Please strictly follow the instructions and warnings before using this product:
It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.The output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.This interface can output 0-10V analog signalsUSB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.This control board does not require any drivers to be installed,as long as Mach3 can run, the control card can be used;Support computer system: Windows 2000/ XP / Windows 7/8/10The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability,no interference signal will be introduced due to the introduction of external strong electrical equipment.Whether frequency converter is supported: YesSupport PWM: YesNumber of control axes: X.Y.Z.A axis
Model: S-400W-36V
Output Current:11AOutput Voltage:36VOutput Frequency:85%Output Power: 400WL: Live wireN: Negative wire+V: DC power output “+”-V: DC power output “-“+V ADJ: output voltage regulation
110V or 220V
Input: 110-120V AC or 220-240VPlease flip the side input voltage selector switch
