Ampinvt 60A solar charge controller with LCD Display
12V 24V 36V 48V AutoSolar panel: suitable for 900W (12V); 1700W (24V); 3400W (48V); Maximum input voltage :150V PVRated Solar Charge Current: 60ASupports 4 charging options: sealed, gel, flooding and user definedRS485 communication: Capable of Wi-Fi remote monitoring (Additional purchase required) - Realize real-time wireless monitoring function of solar controller by APP, Simple and convenient to set, One-key restore the factory settings. Suitable for Andriod & IOS system.
-
MPPT Range Operating Voltage:
12V: 18VDC - 80VDC 24V: 30VDC - 100VDC 36V: 40VDC - 100VDC 48V: 60VDC - 150VDCIntelligent DSP control chipset.Intelligent LCD display with multiple function.True Over Temperature Protection.New and original electronic components.Internal circuit lines and signal lines are based on plug-pull blocks, not welding.
Package Included:
1 x MPPT Solar Charge Controller 1 x Temperature senor 1 x Operation Manual
Easy operation, details data display in real-time,
Inbuilt real-time temperature monitor, <42℃C slow fan, >45℃C fast fan, protect inverter from overheat.
Communication protocol is available, capable of Wi-Fi remote monitoring and external screen control,
Big enough for air to go in, but small enough to protect inverter from dust
Attention:
Always connect battery first !! Make sure enough batteries’ voltage let controller recognize the right system voltage. NEVER connect the solar panel array to the controller without a battery. The disassembly sequence is contrary to the wiring order. DO NOT connect any Inverter/ wind/ Alternator or Charger into the charge controller !! Please connect the Inverter directly to the battery.Ensure solar input voltage higher 3V or more than batteries’ voltage and total input power in the range. If input power is too low for max input power, it may be appears to have been discontinued, the charging current almost be zero when controller is floating charge.The charging indicator is on and off, and the charging current is off and on. This situation generally occurs on cloudy days or in the evening when the light is insufficient, which is a normal phenomenon.When the controller is buzzing, it is because the fan is trying to dissipate heat. Please wait patiently.DO NOT install the charging controller in direct sunlight to avoid power loss due to overheating. Remove all clutter around the controller to reduce interference and make sure there is enough space for heat dissipation. ( leaving a space of approx. 20cm )Ensure all connections going into and from the controller are tight. DO NOT let the positive (+) and negative (-) terminals of the battery touch each other. Add to Cart Add to Cart Add to Cart Add to Cart Customer Reviews 4.2 out of 5 stars 208 4.2 out of 5 stars 208 4.2 out of 5 stars 208 4.2 out of 5 stars 607 Price $98.00$98.00 $155.00$155.00 $195.00$195.00 $495.00$495.00 Battery System Voltage 12V 24V 36V 48V 12V 24V 36V 48V 12V 24V 36V 48V 12V 24V 36V 48V Rated Current 40A 60A 80A 120A Carton Size 191*215*89mm 365*290*160mm 230*279*91mm 303*436*138mm G.W 3.5KGS 3.6KGS 4.5KGS 13KGS
Package include:
4Pcs 23HS2430B Nema23 Stepper Motor 112mm,425oz-in,3A4Pcs CW5045 stepper motor driver 24-50V DC,4.5A1Pcs 400W 36V DC 11A DC switching power supply1Pcs 4 Axis USB Mach3 Motion Control Card1Pcs USB cable1Pcs CD disk
Motor Type: HybridStep Angle: 1.8 degreeHolding Torque: 425oz.in/2.8NmRated Current/phase: 3APhase Resistance: 1.6ohms ; Inductance: 6.8mH+/-20%(1KHz)
Frame Size: 57 x 57 x 112 mmBody Length: 112mmNumber of Leads: 4Weight: 1.66kgFront shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length
Our motor is made of solid and durable metal. The perfect combination of rubber and rotor makes the internal structure more stable, and also reduces the vibration and noise when the engine runs.The motor runs more quietly, with a high torque of 425oz in. The coil uses pure copper enamelled wire to ensure that long-term operation will not lead to excessive engine temperature.The rotor surface is coated with high-quality epoxy resin adhesive to isolate the adsorbed burrs on the rotor surface, more stable magnetic field and longer service life of motor.
Stepper motor's red wire connect to driver's A+ portStepper motor's green wire connect to driver's A- portStepper motor's yellow wire connect to driver's B+ portStepper motor's blue wire connect to driver's B- port
Electrical Specification
Dual Shaft
Material
Wiring
GND：DC power cathodeVCC+：DC power positive poleGND：DC power cathodeA+、A-：Stepping motor one windingB+、B-：Stepping motor other windingPUL+、PUL -：Stepping pulse input+5VDIR +、DIR-：Stepping motor direction inputENA+、ENA- : no need to connect
Dimensions: 118mm×76mm×33mmShape design is convenient for installationWorking environment: Temperature -15-40℃ Humidity<90%
High-performance motor driverMircostepping: 1(1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5, 1/10, 1/25, 1/50, 1/125, 1/250DC power input type: 24V~50VDCOutput current: 1.3A-4.5APhase: 2 phaseWeight:＜300g
Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.Support for connecting electronic handwheel;MCU model: three generation 32-bit STM processorCommunication plug-in: RnR motion control card - ECO-2.0
4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device.
Support for 4 Axis linkage, you can connect four stepper motor drives or servo drives;Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;Have 0-10V signal output,you can use mach3 software to control the spindle motor speed.One status LED, indicate connection status on the board.
Please strictly follow the instructions and warnings before using this product:
It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.The output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.This interface can output 0-10V analog signalsUSB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.This control board does not require any drivers to be installed,as long as Mach3 can run, the control card can be used;Support computer system: Windows 2000/ XP / Windows 7/8/10The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability,no interference signal will be introduced due to the introduction of external strong electrical equipment.Whether frequency converter is supported: YesSupport PWM: YesNumber of control axes: X.Y.Z.A axis
Model: S-400W-36V
Output Current:11AOutput Voltage:36VOutput Frequency:85%Output Power: 400WL: Live wireN: Negative wire+V: DC power output “+”-V: DC power output “-“+V ADJ: output voltage regulation
110V or 220V
Input: 110-120V AC or 220-240VPlease flip the side input voltage selector switch
